Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
Hi NordicSemi
I have a project where we receive data via the UARTE. To avoid missing data caused by higher prioritized tasks we want to use the DMA facilities.
nrf52832...
Hi,
i want to flash programs with the Segger Embedded Studio to my Thingy 91. I already am able to flash hex files with the nRF Programmer to the thingy 91. I installed...
In addition to (obviously!) a 52811 chip and a BLE beacon, what additional hardware would one need for reasonably accurate location tracking of a BLE tag/beacon? I'm generally...
Hello Devs,
I have enabled NRF_LOG in my project, but I would like to disable it in, for example, the main.c file, but keep it working in others files.
at the moment...
Hi all, I am stuck with a simple but weird issue. It's driving me crazy for the last few hours. I am using a PCA10056 DK. I am somehow unable to do a simple digital pin read...
hi ...
I am working on mesh 3.1 version . I have used light switch example . In this case , i am sending the character in generic_onoff_set_cb , and changed from bool to...
I am trying to pair the BleHeartReteMonitor example in pc-ble-driver. I have gotten to the point where I get the pairing request from the central and I get its capabilities...
Hello, Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0
I made my app_error_fault_handler. It is very good for me.
I sometimes got an error. So I saw that log...
Hi guys I m trying to send a simple message every time a gpio interrupt occurs on the client in order to receive that on the server. I m using the ble mesh protocol and I...
Hi
We will use the 52811 together with nRF9160 for short range communications. Currentconsumptionwise which interface is recommended, UARTR, TWI or SPI?
I am trying to run the example secure_bootloader\pca10040_ble_debug. The application does crash during a debug print with following stack trace:
Any idea what could...
I've reached a critical point in the firmware development process where I need to start considering integrating a bootloader with the application code.
I have a custom board...
Hi,
I'm trying to update the modem firmware on my nRF9160. I believe the current firmware is mfw-m1_nrf9160_0.6.8-30.alpha. I followed Martin's suggestions here , but nRF...
Hi,
If i had a purpose of including Ble files into peripheral example then what is the way i can approach?Is it by including all neccessary header file paths,adding sources...
