Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello to all,
We are using nRF52840 with SDK v15.0 using SES, Our application is we have sensor devices with interface WiFi module. Sensor device will wake up as predefined...
I am trying to get a simple spi setup working. Through the dev zone I found a link to this https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160...
It seems like several people have been able to order nRF52840 WLCSP. I checked all of the Nordic recommended distributors but none of them have stock. Would you suggest distributors...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I'm following pc-ble-driver compilation steps.
I could run "vcpkg install asio" and "vcpkg install catch2", but "vcpkg install --head spdlog" fails with error:
C:\dev...
Hello, I am usering nrf52840, now i am testing the current. i found that the current is 40uA in 0dBm while 201uA in 8dBm. maybe it is abnormal in 8dBm, what can i do to check...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi, I am fiddling with this example from the SDK: infocenter.nordicsemi.com/in...cp=5_1_4_3_1_2
In this example, there is a test regarding key derivation as:
As I understand...
I am getting intermittent pickup of advertising packet from a peripheral known to advertise every 2 second. Basically I get ~20 sec gaps where nothing is received.
Below...
I want to use the ble in nrf51822, and I use the example in nrf51_SDK_11.0.0 and softdevice in nrf51_SDK_11.0.0 \s130nrf51201\s130_nrf51_2.0.1_softdevice.hex(thougt the example...
Hello
I am currently looking for the best method to write and read values in the flash. My values are 17 uint16_t arrays with 216 indices per array. I would like to store...
Hello All I am new to this nordic semiconductors. I need information regarding nRF52840 DK boards.
* How to connect two nrF52840 DK(transmitter to receiver) and start advertising...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
