I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I need to send data to an APP through NRF52832/840
This data will only be sent when there is a match with my APP. Once I have established a first communication with my APP...
Hello!
Hello, I have an Issue with NRF51822 chip, made an over 25k messages per second transmitter based on Keil example, but the main difference is that I dont enbable...
Dear all,
In my project, I add 3 long push action events related to 3 buttons by using " bsp_event_to_button_action_assign( )". Everytime I long push any of 3 buttons, the...
Hi,
I am trying to program the bootloader for the nrf52840. I am trying to create a settings for the specific hex file, and then programming using the nrfjprog commands...
Hello,
I use a custom board for an IoT application. The BLE module I use on this board is Taiyo Yuden EYSLCNZWW which uses nRF52810 and requires softdevice s112.
I already...
Hi all, I've been testing 6loWPAN over BLE with the nRF52 DK ( nRF52832) using the IPSP sample code from Zephyr OS, and have managed to successfully flash the code and establish...
Hi all,
I have a Raytac MDBT50Q-DB board which I was programming using an nRF82540-DK. It all used to work fine, but now JLink cannot connect to the Raytac board anymore...
Hello,
I'm using nrf52 DK with SDK 14, to flash a Taiyo Yuden EYSHCNZWZ module ( Module Datasheet ). The flashing is successful, as stated by the output console in Segger...
I am a master student. I am working on a project that uses Bluetooth 5 Beacon Scan.
I bought the nRF52840 dongle to scan the Bluetooth 5 Beacon
I want to scan the Bluetooth...
hello!
I am currently using SDK14.2 (migration to 15.2 WIP) and S132 and on a custom board
requirements - I want to collect data from around 50 (or more) PERIPHERALS...
Hi to all,
i am developing a device with NRF52840 soc and i am using cryptocell IP to create ecc key pair. as you know public key of an ECC alg is a point on spec curve...
Hello All.
I am using the following
SDK Version : nRF5_SDK_15.2.0_9412b96
Segger Studio Version : 4.10
Mesh Version : nrf5_SDK_for_Mesh_v2.2.0_src
I am trying to...
Hi,
I am woking on NRF52840.
OS : Windows
SDK version : 15.0
Dev : Keil IDE.
I am using Timer -2, Compare value method to obtain an interrupt.
The interrupt...
The thing I currently try to implement is to combine two 128-bit services in one app - custom and UART.
I arleady made run them separately - one service at app.
Way they...
Hi All
I have started working on BLE mesh network to control lights.
I have following doubts, please clarify.....
1. To implement mesh network, two options are there...
