Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
I have a mouse that is advertising, and I paired it with my host. It always stays in connected mode. When I press the three buttons — middle, left, and right — for 5 seconds...
What is the recommended termination for unused RF pins on the nRF54L15 in QFN48 (QFAA) package? Can you confirm this is acceptable?
ANT Pin 31, floating VSS_PA Pin 32, grounded...
Hi, I want to change the voltage of the VDDIO in the group of pins labelled Port 1. I launched Board Configurator from nRF Connect for Desktop but it says "This development...
I have code set up to configure Timer3 to generate a Compare event at 100 KHz, using the PPI so that triggers an ADC Sample event for the two enabled ADC channels. EasyDMA...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hi,
I'm developing an application with a custom firmware image for both the nRF52840 and nRF9160 on the nRF9160DK. I've always been on ncs v2.5.0 and decided it would...
Hello,
I am trying to program a custom device of nrf54l15 using nrf connect for desktop app(V5.2.0) -> Programmer(V4.6.2)
I am able to program it but this is how I see...
I am bringing up a custom board using the nRF54L15 (Fanstel BM15M module) and I am using SPIM00 as the high-speed SPI interface. I am configuring the peripheral through Zephyr...
Using PPK to measure the current, it was found that there was a 1-minute cycle signal in the current waveform. No timer was set. The watchdog timer is 10 seconds.
Im currently working on a project which should receive audio through CIS and retransmit it over BIS. Im using nrf5340_audio_dk for this. Ive tried using https://docs.nordicsemi...
Hi,
We came across this feature " PLMN selection optimization during initial search ", enabled by AT%FEACONF=0,3,1 . It sounds good for speed and power consumption.
...
Hi all,
I’m working on a custom board based on the nRF9151 , and using the Ignion NN03‑320 antenna for GNSS reception.
In our GNSS TTFF testing (using AT commands),...
I'm developing a keyless entry/start system for vehicles with the following requirements:
The vehicle side uses an nRF54L15, while the mobile phone is a standard smartphone...
Hi,
I am developing an audio application on nRF54L15. I have successfully used the Zephyr API to read sequences from the ADC with extra samplings (the "extra samplings"...
Hi.
Goal I am creating a new application for the nRF54l15 and want to follow the latest recommendations for project configuration. I need to do DFU over BLE, so I'm trying...
