Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I have added the Buttonless Secure DFU service to my application so that the app can be updated over BLE. It seems working. However, the power management module must...
Hi,
1. In my last post, ( https://devzone.nordicsemi.com/f/nordic-q-a/60300/questions-on-usbd_cdc_acm-example ), in question #1 a nice explanation was given regarding the...
Hi,
I am wondering if there solution available to perform DFU using Windows 10 OS? Going through previous tickets, it seems that there is no easy solution to perform DFU...
Support,
I am using the ble_app_gls_pac19956_140 example on the nRF 52840 DK. I wish to use this application as a foundation for my new sensor.
I wanted to disable the...
SDK: 15.2 IDE: Keil Softdevice: S132 v 6.0 General question about PPI connections. Is it possible to setup a PPI channel, that when triggered by some event (e.g. value in...
Hi,
I'm trying to lower the power consumption om an Actinius Icarus board which uses an nrf9160 chip. I've been able to achieve a sleep current of 1.33mA and I'm not able...
Now the code in the application part has added the buttonless_dfu function, which has also been successfully implemented. But I ’m not familiar with serial_dfu, I don’t know...
Good Afternoon:
We are developing a BLE remote button using Nordic's nrf52840. We have purchased several devkits and are in the process of fabricating our own design specific...
Dear,
Im trying to use the motion to activate the GPS and deactivate GPS:
1. when it moves, GPS will be activated: Position-ON
2. when it stops, GPS will be activated...
I'm working on an nRF52832 based IOT product using Segger Embedded Studio for ARM v4.50 on my Windows 10 machine. My project uses FreeRTOS. Looking at the release notes for...
Hello,
This may be normal behavior once correct connection management code is in place, but I want to verify since originally I was looking at 2-3 minute connection times...
I want to use a comparator without interrupt.
The measurement is not time critical.
Therefore, I chose the LPCOMP.
For initialization I use the following code:
For...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
