I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
SDK14+Nrf52832:
I want use one pin as a interrupt pin.
when the pin level from high to low, execute A task;
while when the pin level is from low to high, execute B task...
Hi Folks,
Windows 10, clean install of ncs v1.2.0, using nRF5340-PDK with SES 4.42a. Project blinky rebuilds and runs fine. Now I need a zephyr example of creating a simple...
Hi,
What is the suggested way to switch between 64MHz and 128MHz on the application core? Normally I want to run at 64MHz, but sometimes boost it to 128MHz. Is there additional...
Hi,i use the bootloader demo code , the file path is nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble\arm5_no_packs ,a fter I compiled and passed,...
Hi,
I know this question has been asked a million times before, but most of the links are now dead, and the advice seems stale. On sdk 15 and up, how do I go about setting...
Working on a BLE application on a nRF52833 development board with FreeRTOS (external/freertos), and I noticed that the SDK uses dynamic allocation for FreeRTOS, e.g., xTaskCreate...
Hi community, I need some help with mesh programming cause i'm new to it ! First, i'll explain what i've done : I create a program on visual studio, which can communicate...
Hi,
I am starting a new iOS BTLE project for a new kind of music instrument. I started with the Thingy believing that that would be a good reference design to start from...
Hi!
Working on project based on nRF52810. Everything was fine until I began to work on part to save setting in flash memory.
I've used flash_fds example SDK 16.0 as starting...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
I'm trying to get the debug version dfu secure bootloader from nRF5SDK160098a08e2 running on a nrf52832.
I'm able to compile it using cmake and a gnu c compiler. However...
So I am doing a project with a 160x80 TFT display, using the ST7735 driver. I have slightly modified the ST7735 functions to work with my display, and everything is running...
I am trying to create an application which would send data once a minute. The application is based on BLE advertising packages, because it should be the most simple method...
Hi,Sir：
I am making a DEMO based on SDK15.0(SDK15.0\examples\ble_central\ble_app_hrs_c) and pca10056 for my one of important customs.I need to implement some extra software...
Hi,
I am now in Hong Kong, and trying to connect to NB-IoT network here. There are 2 providers of NB-IoT in Hong Kong: "CMHK" and "Three". They provide NB-IoT since 2017...
