I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Dear Support,
In our new project, we have 8 signal LED diodes attached to nrf52832, they are all sinking current:
3x GREEN 0.8mA (P0.16, P0.17, P0.18)
1x RED 3.3mA...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hi,
I'm using SDK 15.2. I flashed the dtm firmware on the BLE chip. How can I test its working before sending it to the certifier? I have nrfgo studio & I'm able to start...
Hi Team
We are able to flash nRF52840 based LE Module using nRF52840 DK successfully.
But we would like to know if nRF52 DK also can be used to flash/program this nRF52840...
Hello,
SDK:15.3
If not pair with moblic phone, spi is normal
And obile phone pair 52811 to send data, that also normal
But I want to integrate, then 52811 is NRF_BREAKPOINT_COND...
Hi all:
For SDK15.3, if I want to change 32.768Khz to internal LF clock, Should I enable the CLOCK_CONFIG_LF_CAL_ENABLED of "sdk_config.h" ?
if I disable CLOCK_CONFIG_LF_CAL_ENABLED...
trying to implement an external interrupt with both edge triggered. I wanted to try first pin_change_int example in sdk 15.3.0 but it is not compiling. I didn't do any change...
Need to communicat between nRF52810 and nRF24L01. nRF24L01 is standard module from Nordic. we are using nRF52 development kit and using Segger Embedded Studio (as suggested...
