before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello everyone,
I am trying to add new service into ble_app_uart example. I compile successfully. I do not get an error. But the device is not advertising. I can only advertise...
In my plan, I have used NRF52832 IC as the transmitter and the NRF24LU1P+ as the receiver. I have tested the wireless transmission successfully. In order to reduce consts...
Hello,
I get the sources from Thingy Mesh Demo and use the guide to build it examples. Thingy_node build without errors, but Thingy_bridge return the error "too few arguments...
Hi
I am using nrf52832 doing a project and I 'm new to this MCU.
My project concerns sending data from APP via BLE to nrf52832 to config parameters of SPI (data and clock...
Hi,
I am trying to modify the multilink central example to send string to other board (peripheral)
I already did the UART configuration and in my tests I saw that when...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
We are trying to modify the nRF Beacon example app for iOS that Nordic provides. We are unable to get app to see the devices from the iBeacon kit when they can be seen from...
The manuals for the nRF51 and nRF52 list the maximum ESB radio channel number
as 100, but in the SDK the guard value in the set channel function is <= 125
(in both the...
I am about to start development on a project that will be using a pair of nRF52832's to make a low data rate connection between a PC (with a nRF52832 based dongle) and a device...
In the event that a Nordic soft device library call fails (as determined by APP_ERROR_CHECK() macro) and our application level app_error_fault_handler () function is called...
Hello,
Ported my FreeRTOS application on NRF52 from SDK 12.2.0 to SDK 13.0.0 .My application is using freertos apptimer for timestamping and waking up of device which was...
Hi,
I am trying to run a ble mesh example but I prefer to work using keil, because I already worked other examples using the SDK (12, 13 and 14) and PCA10040/PCA10056 nordic...
For a precision timer application I have an external temperature compensated RTC (DS3231) which produces a highly stable 32 kHz signal connected to pin 5
When I associate...
Hello,
I am rather new to BLE and the NRF5x.
I want to build the following application: a swim timing sytem. The system consists of master timer with a high precision...
