My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Dear friends, 1) As shown in the pic below, there are some values "max:13.70, min:3.33, rms:3.45..." at the bottom of the pic. which area is these values calculated from?...
I'm finding fairly large lags with the RTC2 I'm using. I use an app_timer to sample the current RTC count value as a timestamp (MM:SS:Hundredth-of-a-second) and send it out...
Hi all,
I have a question to complete the tutorial 'Setting up device firmware update(DFU) on the nRF5 DK'. this
I have tried to set up my nRF51 Development Kit.
Everything...
I am facing wierd behavior after migrating to sdk 10 serialization code i.e ble_connectivity example program. Unable to scan peripheral devices, some times unable to connect...
in SDK14 I'm trying to add an SD card into the BLE central example.
The SD Card example compiles and runs OK. Problem happens when I combine that code into ble_app_uart_c...
Hi,
I'm checking whether SDK 13.0.0 secure bootloader dfu can proceed correctly with iOS DFU library if the process is interrupted because smartphone application is restarted...
Hello,
I want to enable UART only when it is necessary to send data.
I want to use ble_app_uart_low_power_master or ble_app_uart_low_power_slave
The URL of ble_app_uart_low_power_master...
Hello,
I've been working on the ble_multilink example and managed to combine that with the ble_hrs_c example to connect to multiple heart rate units and receive the data...
I create software uart librarty for nrf52832. For one pair tx, rx it's worked (on 9600, 19200 baudrates). Then I create multi-instance software uart (all of them gonna use...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
The SAADC on the nRF52832 consistently reads 20-30mV low, regardless of the source (AIN channel or VCC), Tacq, Resolution, or gain. All of the measurements are using the internal...
HEllo,
I am trying to set up a whitelist advertising and scanning, and while the advertising seems to go fine, I am getting an APP_ERROR:ERROR:Fatal on my central while...
Hello all,
Accordingly with nrf52832 product especitifation when radio Rx is active there's a additional 5.4mA consumption. My doubt is how softdevice s132 handles the Rx...
hi!
i am working with the nrf52 and i am looking for a timed sleep mode, meaning, a function that goes into sleep mode for a given duration.
is there anything like that...
Hi all,
I am working on my Central device to request pairing to my peripheral ( I asked about the peripheral in my previous post , both are running a nRF52DK and SDK13...
