I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
Is there someone I can contact about acquiring some sample chips for prototyping? The normal distributors don't seem to have any information regarding the engineering samples...
Hello,
I am currently working on a project involving the nRF52DK to be a central device.
The peripheral device is based on the Nordic Uart service with minor changes...
hi，
i tried add ancs to the s130 ble_app_hrs_rscs_relay demo， when i use iphone5s to connect， the uart display as follow，but when i receive a message or a call， the software...
In GATT Packet transfer, is there occurs any packet loss and retrial?
I'm trying to connect about -90 Rssi dBm peripheral device with my nRF51-dk.
In this far range...
Hello,
when I was working on MSP430 I used to place the firmware version constant at a known address in flash so that it can be verified which firmware version is flashed...
I was having some troubles using the app_timer (RTC1) shortly after mesh startup, so I enabled the PIN_IN_CB and PIN_IN_TS debug pins, and saw some interesting behavior. ...
Hello all,
am trying to configure 3 adc channels in a way to have conversion in 3 differents pins, without usin timer and ppi. so I implement the following code, the problem...
Hi
May i know what would be the debugging procedure using segger-RTT for nrf52840 and what is the debugging Hardware Required ?
Thanks and Regards,
R Madhu.
I know BLE5 is the future of IoT. I also want to invest on it.
But how to setup a complete BLE5 environment? In China, IPv6 has not been supported. Therefore, 6LowPAN/Thread...
Hi,
I want to ask a few question for ble_mesh.
What do these functions do:
rbc_mesh_persistence_set(..), rbc_mesh_tx_event_set(..)
Who should do the set operation...
