Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
Hello,
i have one PPK2. Recently i find the current reading from PPK2 is relatively large compared with actual current value.
For example, actual current value vs PPK2...
I've been using the ppk2 power profiler with version 4.0.1 for over 2 years and it has worked very well in providing a power source and monitoring/ with reviewing the power...
Hi all,
I'm doing some tests with the nRF5340 DK to log with a custom timestamp source. I took the logging exercise 2 example and verified that the log messages are correctly...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
Hi,
I've just migrated my project from NCS 2.6.1 to 2.9.0 and I'm having some problems with the UART.
I'm using the nRF52833 DK to communicate with another device and...
Hi, I'm currently working on adding DFU over UART to my firmware running on an nRF52dk/nrf52832. To have a minimum viable example, I'm trying the DFU over UART exercise sadly...
Hi Support Team,
I met a conflict situation. Could you help give me some guidance?
The project is based on nrf5340 and ncs V2.5.2. The device supports BLE FOTA and works...
Hello,
We've recently updated our BLE-USB bootloader from using SDK v15.2.0 to v17.0.2 and noticed an issue. Our USB-BLE bootloader was created with the USB-serial bootloader...
After completing the OTA update, I executed the "otasoftwareupdaterequestor read-event version-applied" command but was unable to read back the version.
I then tried the...
I am trying to control ws2812 LED (1 LED) with NRF52840 using nrf connect SDK, I was able to control it with no problem when I set building optimization to debug optimization...
Hi，I would like to know how it works when reconnecting after a timeout disconnection，I didn‘t find the answer after reading Bluetooth 5.4 specification.
Hello,
I'd like to download the latest MDK for SES - links here appear to go nowhere: https://www.nordicsemi.com/Products/Development-tools/nRF-MDK/Get-Started?lang=en ...
