Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, In my project we are using the ESB between a nrf52811 and a NRF5340dk and are trying to evaluate the maximum speed we can reach with ESB packet transmission without acknowledge...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Advertiser...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
I just flashed a new image on my device using MCUmgr. In the logs, when the device boots up, it shows the correct APP_VERSION string.
returns:
I: Firmware version: 0...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
I'm following the tutorial Exercise 1 – Custom board for single-core SoC using ncs v2.9.0 with one slight difference in that I'm using a nRF52DK with nRF52832 because that...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
