Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
When trying to write the bootloader hex file to the device with nRFgo Studio, the following error message is displayed.
[nrf52840_xxaa_s140.hex programming failed: This...
Hello
I'm using SDK 15.2 on nRF52 DK to test the ble_app_multirole_lesc example.
I downloaded the code to nRF52 DK to act as central.
I commented the scan_start() function...
I take bootloader_secure_ble example for pca10056 build it and use hex file to program using nRFGo Studio get error verification Failed. if i programmed with keil then load...
HI,
I'm having a problem when I use the function nrf_drv_twi_xfer. The function returns the error code NRF_SUCCESS, but using the event handler I notice that I'm receiving...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
Dear all,
I am using SES, I have an application that relies on a softdevice. For it I developed a custom bootloader that DOES NOT rely on the softdevice and only transfers...
Hello, Nordic! I'm developing with a nRF52832, a bmi sensor and SES. I am starting with the BMI160 libraries on github and encountered some problems with the call of the i2c...
I am trying to implement a simple matrix 4X4 keypad. I have an issue in enabling gpiote events. I disable gpiote events when there is a row event and i scan the keys by turining...
Hello,
We were wondering under what conditions the SIM will reset. AT commands will give us activity on the SIM_CLK and and SIM_IO lines, we are looking to see activity...
Hii,
I have two question regarding advertising and connection
1. Is there any way to hide my peripherals advertising from any other central scanner .
2. Is it possible...
Hi
I did test two sample code with nrf52DK kit in segger embedded studio. with sdk ,nRF5_SDK_15.3.0_59ac345
1) ble_app_uart (I connect one sensor with UART,I did some...
Hi,
we are progress of designing custom board using nRF9160.
By reading nRF documentation, my understanding is GPS circuit in Dev kit is unstable/nonperforming.
Could...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. The first time I flash to the nRF52832 a SIGTRAP occurs on sd_softdevice_enable. I cannot continue...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
When I run the demo of b le_app_hrs on my development board,I use nrf connect app to...
SDK 13, softdevice 132
function fds_register results FDS_SUCCESS
by calling the function fds_init debugger stops, see comment in function below, and i see "unknown...
