I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
Today ,I look up the SDK revisions，found that SoftDevice S130 V2.0.0 support NRF51822 V3.Now my production use S130 V1.0.0,but Chip revision unknow(N51822 QFACA2 1921DC).Is...
I have an application based on ble_app_hrs_freertos from SDK14.
Sometimes the application will not start advertising. When this happens, it does not help to power-cycle device...
Hello, I start in programming on nrf9160 DK. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hello,
Good Day!!
My question regarding the reset functionality of the device.
Reset the device on the short press of the reset button and on Long press (for example...
Requirements:
Transmit an advertising packet that can be received by a native IOS App & a native Android App.
Using an nRF52810, I need to set it to Advertising (non-con...
hi,
The data is sent to the app by sd_ble_gatts_hvx(), but the data obtained by this app is wrong.
When salve sends a byte, the data obtained by the app is always 0,but...
When I download \nRFready Smart Remote 3 nRF52 v1.2.1alpha\nRF5x SDK-SR3\examples\ble_peripheral\smart_remote_3_nrf52\Projects\Firmware_nRF52832 to my 52832 device, I can...
Hello everyone,
I am modifying the ble_central_uart example to connect directly with a device using its MAC address. For some reason I don't understand, it doesn't find...
I am getting an NRF_ERROR_INVALID_ADDR when using the SDKv15.2.0 call nrf_sdh_ble_enable() with softdevice s332v6.1.1
The ram start address provided to the function is...
Hello,
I am creating a wearable PCB with the Raytac MDBT4Q-P BLE module, which uses the nRF52832. I need this device to have OTA firmware capability, but I'm finding it...
