Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
The datasheet shows example circuit configurations with C3=C4=1pF and L1=3.9nH. But the downloaded reference design shows C3=0.8pF, C4=0.5pF, L1=4.7nH, plus an empty...
I try to incorporate the usb dfu trigger into my application. However when using nrf Connect for Desktop to flash the nrf52840 dongle it can not reopen the dongle.
This...
I'm using SDK 15.3 and Mesh 3.20 on a system, that works fine with LPN and nodes with friend-features. The LPN can initiates (establish) friend connection, request status...
Hi !
In order to consume lowest current，we use the function power_manage() ，let the MCU go into sleep，the SD is S130, V1.0，we enable the GPIOTE，watchdog ，ADC ，app_timer...
Hai, I'm trying to learn the UART using the example code available in nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart. I'm using BMD-300 Evaluation Board. I'm...
I am looking at the NRF52832 for some projects and so downloaded the SDK and opened an example project in Segger Embedded Studio (SES). I was shocked to find that the directory...
Hi Devzone!
I'm using UART for sending AT COMMAND and receive the response from lte modem.
I use LM5 which is LTE modem made by m2mnet.
I thought It can be implemented...
I updated to nRF Connect 3.0 today and its seemed to causes issues with any Dongles I connect to my PC. I get the following error:
ERROR Unsupported device with serial number...
Hello,
I want to use the nRF52832 as native transceiver 2.4GHz and I'm looking at examples of the latest SDK.
I'm using Segger Embedded Studio.
I found some examples...
Hi, I'm on final development stage of my custom board. I'm using nRF52840 with nRF5 SDK v15.0.0 and S140 SoftDevice v6.0.0. I need to trace the over-the-air communication...
I'm not using a softdevice, and am doing some time critical measurements when the radio begins transmitting.
This code works very well with nrf51:
__disable_irq(); NRF_RADIO...
Hello
I have a question i cannot figure out. I'm using my phone to send string on my NUS client (NRF52 with SDK15.3.0 and FreeRTOS) and the event BLE_NUS_EVT_RX_DATA is...
Hi,
I am new to development with Nordic chips. I am using nRF52840-DK (SES,nRF5_SDK_15.3.0_59ac345) to read analog input on ADC pin AIN0. I want to continuously read the...
