Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi, I followed through this tutorial:
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
But to my frustration I realized...
Deer friends,
The nRF Connect BLE app supports the configuration of the local device's GATT attribute table, also known as server setup. Adding attributes to the server...
Hi
I am researching options for my bachelor project which happens to be about bluetooth 5, where I am looking to develop a smartlighting system using Bluetooth 5 mesh....
Hello Nordic Support!
We are making a prototype that connects the battery to Vcc, but 5 out of 10 It works properly. Conversely, the remaining five do not behave as expected...
Dear friends,
In the Power Profiling Application (an example of nordic SDK), the priority of the application timer is set to APP_LOW(as shown in the pic below).
However...
stdio.h defines vsprintf and _vsprintf, and suggests using _vsprintf if you want to save on code space.
extern _ARMABI int _vsprintf(char * __restrict /*s*/, const char...
As per the Bluetooth Spec (v5.0) Page 2323-2324, it seems that LE Secure connections pairing supports 1-way OOB. See section of text below.
If OOB communication is possible...
Once GPIO is pressed (shorted to ground), I want to change the value of UUID or Major/Minor number
If not, the device will continue to advertise the previous values
Hello,
I am working on a custom project with nRF52832 using SDK14.2 and s132_nrf52_5.1.0.
Now I am trying to configure and use RTC2, and face the problem that ble_stack_init...
Hello everyone,
after hours of python module installation, I was able to run the PPK with PCA10056. I have cut the SB40 and used an external pwoer source with 2,5 V. I have...
Hi I have two problemes, I do not know where to start, so if someone has an example, I would like to see it. The first thing is if someone has an example about using pwm to...
When registering a base UUID with the SoftDevice via "sd_ble_uuid_vs_add", a uint8_t is returned which (per the ble_app_pwr_profiling example) is intended to be the "type...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
