I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, Currently, I have a problem that I can not see the device on the nRFConnnect application when my firmware is running on the board that has only ISP1507_AL module based...
Hello Nordic team,
I found nRF5340 a very interesting device for our projects. Could you clarify two moments about it:
1) What PCLK frequency is used for application processor...
Hi,
Using the nRF9160DK, an orange SIM card, MODEM firmware mfwnrf9160101 , I managed to make run the sample code: mqtt_simple .using NBIoT
My setup is up to date October...
we are using a device that uses the Nordic NRF 9160. We want to use the device on the Verizon or AT&T network in the US but both providers tell us that the device isn't approved...
Sir,
Downloaded latest nrf-Toolbox for Android v2.7.3 and Android Studio
When I select run to build app get 0 Edit Configuration
How should I fix this problem.
...
On commit 668e0494fee1fc1f7e230124c11bc42f66469e3b from https://github.com/NordicPlayground/fw-nrfconnect-nrf.git
Using SES 4.20a for Mac OS X, I get this:
1> /opt/gnuarmemb...
I receive this output from west when trying to build the asset_tracker example from either master or v1.1-branch:
west build -b nrf9160_pca20035ns -- west build: build configuration...
Hi
I am using a buttonless DFU to do OTA for my application. Everything is working fine up to now, but now my custom board got few modifications of using PIN 16 for USB...
I am trying to complie Eddystone project which is part of NRF5 SDK and when i compile the project in Embedded Studio I get the following error
/resized-image/__size/738x210...
Hello. I am developing with the following configuration.
In this configuration, since it is necessary to connect multiple peripherals with multiple roles, "scan_start...
Since migrating to the Zigbee 3.1 SDK I have noticed a few oddities with the behavior of attribute reporting that I am thinking are related to the following bugfix:
The...
HI,
I find that the DFU code start address regsiter is different between SDK15.3 and SDK16
SDK15.3
MemorySegment name="uicr_bootloader_start_address" start="0x00000FF8...
Hi,
I'm using the Home Automation profile of the Zigbee protocol and, in particular, I'm developing the Window Covering Device, present in the SDK "nRF5_SDK_for_Thread_and_Zigbee_v3...
It appears the softdevice gets into a strange state when a BLE connection is lost while transferring data. How does application code reset or reinitialize the softdevice ...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
