This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello Nordic Guys,
We are working on the system based on BLE_APP_UART_C (central) and BLE_APP_UART (peripheral).
“Central” is always “ON” and scanning for the peripherals...
HI there,
I read somewhere here that the SPIM3 bus would be capable of 32MHz operations in the "next" chip revision (that was 6 months ago).
Could you confirm that it...
I have created a device that will connect and pair with one central. I would like it to re-connect automatically after disconnecting because it was out of range or turned...
I can connect/pair/bond to the nrfConnect app and disconnect then reconnect just fine. When I try to do the same to a central running on arm bluez 5.43, the second and subsequent...
I am getting a SOFTDEVICE: ASSERTION FAILED after some time when advertising with whitelist. I am using NRF5_SDK 14.2.0 and have tried both softdevice s132 5.0.0 and 5.1.0...
Hi,
I am trying to use the fstorage lib in SDK 12.3.0. My code is based on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
I'm sampling from the SAADC with a microphone attached and need to send the sampled data over ble to devices, and I want the devices to recognize the data as being a audio...
I need to develop a beacon application with the OTA DFU capabilities (Buttonless). I have the NRF51-DK.
As a starting point, I tried the bootloader example located in the...
Hi,
I'm designing a pcb for nrf52832, and acc. to specification sheet (2nd para under fig. 98) i need to use differential mode to avoid ground bouncing. Can I share a pin...
Hi DevZone,
I am going to implement Arduino CAN bus shield on nrf52840 preview DK. I am wondering if I can use the Arduino CAN bus library in the nrf52840 preview DK. As...
I'm using sdk 14.2 and I have nrf52832 board. Now when I go to armgcc folder in sdk of any example (I'm using the blinky example ) and open my command prompt and try to build...
Hello,
In SDK14.2, select an armgcc project, for example, pin_change_int.
For nRF52840, the heapsize is defined in /components/toolchain/gcc/gcc_startup_nrf52840.S,...
Hi,
I've compiled the pc-ble-driver-py library on a raspberry pi but it doesn't come with a "make install" command. Could someone help me get the right file structure so...
Hi,
I am looking library for EINK Epaper display. The display I am using is https://www.waveshare.com/wiki/1.54inch_e-Paper_Module
Can I get library code for this?
