This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I want to check out the long attributes capabilities of the S110 SoftDevice.
Inside of the Sdk 5.2.0, I cannot find an appropriate example.
I'd found some example code here...
Hi,
How to work with the connectable directed advertisement (BLE_GAP_ADV_TYPE_ADV_DIRECT_IND) event?
I modified the ble_app_template application to support direct advertisement...
Hi,
I am developing a test board with a nRF51822 and ST balun (NRF01D3) and a chip antenna (probably Johanson 2450AT18A100 or B100). The board will have 4-layers. The inner...
nrfgostudio_win-32_1.15.1 program softdevice s110_nrf51822_6.0.0_softdevice.hex works well with STlink for nrf51822 but when I program bootloard error appear :
Running...
Hi,
I'm using the redbearlab shield in combination with an arduino uno r3.
I want to send sensor data at about 10 hz to my smartphone.
This works but sometimes I get...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hello,
I am trying to get the PCA10001 evaluation board going with BLE, and am trying the ble_app_hrs example from the SDK as a start. I am developing on Mac OS with Eclipse...
Im trying to have the s120 modify the value like I would in Do a Read all records operation in the Glucose example. I cannot figure out what function would enable me to do...
The SDK function sd_ble_uuid_vs_add may return NRF_ERROR_INVALID_ADDR If p_vs_uuid or p_uuid_type is NULL or invalid.
When the pointer is not NULL, how does this function...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi we are using NRF51822 board.
i flash ble_app_hrs application. then it is giving advertisement.
but when i call twi_master_init() function from main. advertisement...
szenario
beacon and receiving nodes are all MCU based and all powered by net, no local battery needed
the beacon usually located near the floor, the nodes will be located...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
