This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I'm trying to figure out how to change the start address of my application when chip has a bootloader flashed on it.
For example :
Bootloader address = 0x0
Main application...
Hi,
Fairly new to the world of nrf development and C programming so apologies for the potential newbie question.
I am looking at how I can setup a Raspberry Pi 4 as...
I have an application that uses the nRF52840 for BLE in central mode. This application is battery powered. Basically, the device is listening for beacons and logging which...
I'm trying to connect to a device with a public address using an address filter in the scan (not whitelisting), I've seen plenty of similar unresolved issues posted here....
I am searching for the zip with reference designs and PARTNUMBERS for the nrf52 series. The datasheet link is broken and I can not find the ZIP file in the new Help Center...
Hi,
I'm trying to use the serial number of the nrf52832 microcontroller in code, how can I acess it with Segger.
I tried using this code from this link but it doesn't...
Hello. We are planning to change from QFN48 to WLCSP package in our product. However I could't find any guidelines to create the library for Eagle. I was wondering what is...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
SDK: 15.2 IDE: Keil SoftDevice: 6.1.1 Board: Custom Hello, I would like to synchronize an SAADC reading during a BLE transmit event. The power source to my board is a CR2032...
Hi,
I am developing an application for Thingy:91 in which I want to send data from the device to MQTT server. I am using 1.1.1 modem firmware and 1.2.0 ncs tag.
The whole...
I'm developing a product using an nRF52840 and an accelerometer.
I have created a Service with characteristic that sends accelerometer data over ble to the phone through...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever.I got an err_code NRF_ERROR_INVALID_DATA. Softdevice is s132nrf52611...
Hi,
I have a custom board with the nRF52840.
Is it possible to customize the DFU to be able to update the firmware through other interfaces than BLE or USB/UART?
I have...
Hi, I'd like to set up cccd here, but test the error,
In the routine nRF5_SDK_15.3.0_59ac345 nRF5_SDK_15.3.0_59ac345.0_59ac345.s.ble_peripheral?ble_app_uart/pca10040-s132...
