Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Sdk: nRF5_SDK_15.3.0_59ac345
example: nRF5_SDK_15.3.0_59ac345.s.ble_peripheral\ble_app_hids_keyboard
question: After connecting to ios, ios virtual keyboard is automatically...
In some other non-hid app, I can set APP_ADV_TIMEOUT_IN_SECONDS to zero and it worked fine. The advertising is continuous.
But in the ble_app_hids_mouse, I set both APP_ADV_FAST_DURATION...
I would like to use AT commands to get the IMEI on a custom board that has an nRF9160.
In preparation for this I am attempting to get AT communication working on a NRF9160dk...
On the nRF52811 with the s140 softdevice, what is the set of things to do to enter very low power sleep state? The product specification says ION_RAMON_RTC is 1.5 μA. What...
Hi
there I'm having a problem in compiling an application using nrf_esb and app_timer.
./nRF5_SDK/components/properitary_rf/esb/nrf_esb.c:900: multiple definition of...
hi all, i'm trying to disable uart for lower power consumption, i've disables it with: but when i measure the voltage on the rx pin i see 1.8V (this seems to consume current...
Hi,
I'm starting with nrf52 dk using Keil ide for ANT+ applications...
I tried to run an example inside the sdk folder and I have problems with app_error functions....
I have been running a mqttsn client publisher/subscriber project (based on the example) successfully for some months. I have added a mosquitto broker to the raspberry pi border...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
Hi everyone!
I've been using the Power Profiler Kit quite successfully for the past few months. Instead of using the UI, I designed a python app to communicate with it ...
The nRF52840 OPS 0.5.1, describes nWRITE,BLOCK as the amount of writes allowed in a block between erases, and lists nWRITE,BLOCK = 403 Maximum.
It looks like 8 blocks are...
Hi folks,
I have a system basically working with the following setup:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) #define MAX_CONN_INTERVAL MSEC_TO_UNITS...
adv interval : 1s
adv data: 31byte
tx power: 0dBm
MCU: nRF52832
The power consumption is shown in the figure below,when I don't enable DCDC.
what may be the reason...
I followed all the steps mentioned in the tutorials. In one of the threads, it was mentioned to erase all and then try and it worked for some. I tried that as well. Still...
