Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Nordic's BLE page ( https://www.nordicsemi.com/Products/Bluetooth-Low-Energy ) says the nRF5340 is the "ideal choice" for LE Audio. I can't seem to find any information on...
Hallo,
my nRF52840 and my nRF24L01 are receiving the same data in proprietary radio mode.
Several nRF51822 are sending mixed up data.
Within the nRF24L01 - radio Interrupt...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
HI
I still try to reconfigure my Zaphyr testing environment to NRF Unity/CMock but I've encountered more issues.
1. __syscall mocking
Is there any reason to exclude...
Hello there,
I'm trying to interface msp430 (master) with nrf51882 (slave) through SPI. I'm running soft device 110 to broadcast the received data from SPI through BLE...
Is there comprehensive documentation on DFU, mcuboot, and zephyr somewhere? I have an nrf52840-based device running a Zephyr 2.4-based application with mcuboot 1.7 as a bootloader...
Hi, I am trying to interface Max31865 with NRF52832 via SPI communication. My module RTD pt100 working fine with Arduino but I am getting unchanged wrong value while programming...
Hi there,
I have used the nrf2724 (radio module) as a prototyping platform. I am able to flash my personal program to the nrf24le1 on the nrf2724 and it functions properly...
Hello!
I'd like to briefly introduce what I'm attempting to do: I'm trying to flash some samples from the Zephyr project into a custom board. The custom board is based on...
Hi,
I tried to update DFU keys via update on SDK-4.1 and I didin't to do it. Its possible to change DFU keys via upgrade. I did this process on SDK-2 and there was no validation...
