Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi ,
in the RTOS example, you set
configTICK_SOURCE as FREERTOS_USE_RTC and configCPU_CLOCK_HZ as( SystemCoreClock ) .Since SystemCoreClock is 64mhz, why did you not set...
I am trying to understand why when I connect the nRF52840 Dongle using nRF Desktop I get this message in the log:
2020-02-26T23:12:13.293Z INFO Connectivity firmware version...
Hi Team,
We are using nRF 52840 chip for our development of product.
As of now the settings for BLE data transfer are as below.
MIN_CONN_INTERVAL 20 // which is the...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
Hi,
I am using
PCA10056
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am testing background serial-dfu.(refer to https://devzone...
Hello,
We are working with the nrf 9160 dk.
We need to use internet connectivity to send an http get and post to a remote server.
We want to utilize the NB-IoT...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
I use nRF5_SDK_15.0.0
My soc is NRF52832,project is based on ble_peripheral ble_app_blinky.
After I call idle_state_handle() let my device go to sleeping.
Sleep current...
Hello,
We are using nrf52832 with sdk 16.0, for a particular reason we are storing some variables in flash storage, i have some question regarding that
what is the time...
Hello,
I am developing a driver that can handle cryptographic operations and I am using example code from nRF5_SDK_16.0.0_98a08e2 /examples/crypto/nrf_cc310/aes to get...
I have a Segger J-Trace Pro and am attempting to enable trace debugging of my application. I have a custom board that breakout out the appropriate Trace Clk and Trace Data...
Installed nrfutil with python 3.8 and pip3 20.0.2 on Windows 10 Trying to run dfu over usb-serial: nrfutil dfu usb-serial -pkg FW.zip -p COM4 -b 115200
I get the following...
Hello,
I got a problem with the nRF sniffer for Wireshark. I got the following configuration:
Board: nRF52-DK pca10040
Hex file: sniffer_pca10040_129d2b3.hex (provided...
