I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello all,
I am attempting to develop an application which utilizes a third party library for proprietary sensor calculations. This library requires the use of floating...
Hi DevZone team,
Hope you're doing great today. Just want to confirm if the nRF9160 is ready to operate in Mexico. The LTE Bands needed are B2, B4, B5 and B28. The IFETEL...
Hi,
I use SDK 10 pwm example (examples\peripheral\pwm) to modify the PWM cycle to 10s and duty cycle to 50%.
Code showed as below:
But the PWM cycle seem only around...
I have seen the datasheet of nRF52840 but I can't find that any GPIO pin used as SPIS. It says that you can configure the pin those whose value is written in the PSEL.MOSI...
Hello everyone!
I've tried to run mbedtls crypto functions which are using cc310 hardware implementation and I have partitions overlap issue.
Our main goal is to test...
Hi there, I've been testing out handling the Apple Notification Service notifications.
I have set up the handler for the ancs_object as on_ancs_c_evt, I can successfully...
Hi,
I'm currently doing a project where I want to sample an SAADC and send it over Bluetooth to another nRF52840 device with different sampling frequencies. The problem...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi All,
I am new to nordic, i am using nrf52840 development kit and using the SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
I would like to start the program from...
Hello,
i am currently developing on nRF52840 using SDK 15.2.0. I have an application and a bootloader. I use the GPREGRET register to boot to bootloader.
I have an issue...
Hi team,
I have a customer who wants to implement the "nrfjprog --recover" command by using the Chinese copy Jlink. They want us to provide the manual which can explain...
Hi, I'm having issues with building sample applications for nRF9160. I'm constantly receiving warning about BSD_LIBRARY wrong value assigned like below:
C:\Users\lszel...
