Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
Hi guys,
Maybe someone already did this work but if no:
I would like to take only the relevant parts to my project.
I am not sure what can be given up.
I need cellular...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
Hello,
Im trying to flash RAYTAC AN54L15Q-DB board but im keep getting following error:
Error: One or more batch tasks failed: * 1050050051: [Probe] Emulator error: Failed...
Hi,
We are doing RF Test for nRF52840DK, and we are using CBT Bluetooth tester. Commands are going to CBT fro nRF board.
My Question is code we need to flash for RF test...
I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
Hi,
Previously it was possible to download the old nrf5 sdks from for instance this url:
developer.nordicsemi.com/.../nRF5_SDK_v15 .x.x/
but it seems to not be available...
Hello,
I'm trying to read the build info of the Bluetooth LE controller using BT_HCI_OP_VS_READ_BUILD_INFO, but I get the following warning:
<wrn> bt_hci_core: opcode...
I am using nrf5340dk and I am facing an issue. I have configured SPI on my dev kit and the screen I am using with it is operating at 5v but the dev kit has 3.3v max. So I...
Hello,
I am trying to find a simple example of how to setup and run the SAADC on the nrf5340 in continous mode.
I would like to use the internal timer and only need to...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
Hi,
when DC/DC is enabled, current consumption in sleep is higher than when using LDO.
This is consumtion with DCDC = 0
This is power consumtion when DCDC =...
