Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
Hi,
I have developed the firmware using nRF51822 Development Kit. I now want to get to put the firmware on nRF51822 chip used in breadboard. I got a smt adapter with nRF51822...
Hi!
When trying to update app using example bootloader for s110, v.7 from nRF Toolbox I get "Device is not supported. Check if it is in the DFU state".
Bootloader is...
Good morning,
In the application I'm developping with nRF51822 anb S110 SoftDevice, the final peripheral product will be installed in a physical non-accessible place. So...
Hello,
I'm working with the example ble_app_multilink_central of S120. In this example, the scan is done correctly in the three channels of advertising?
Thanks!
I have a characteristic which is a long string. I need to be able to read and write it.
Below is the function for writing to start with. Please comment on this function...
It appears version 7.0 of the SoftDevice 110 supports over the air flashing of softdevice/bootloader/application or a zip containing a combination of the three.
Trying...
Hi,
I'm trying to get SPI (master) to work (nRF51822) for communicating with a quadrature counter (LS7366R).
I've read several implementations of SPI master, such as the...
Using:
GCC 4.8
pure-gcc Setup
Sdk 5.2.0
Softdevice 6.0
I execute some code within interrupt context (softdevice handler) and also in main thread.
I need...
Hi,
What's the difference between a 0.9.0 pca10000 firmware and the earlier version (0.8.0)? I noticed that the throughput with 0.9.0 on the same dongle is much less than...
I'm trying to use the TWI master example with the S120 soft device. It looks like there is a known problem trying to get the S110 working with the hardware TWI. It seems the...
Hello.
I want to make flashing of devices for production faster.
So I want to write application together with bootloader via J-Link simultaneously and not via OTA DFU.
...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
