Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I have the nRF Hw v2, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM10/11/12 device:
Most of the nRF Connect Desktop...
Hello, just beginning initial investigation into nRF9151. Project requires communication to several I2C-based sensors and transmit data directly to cloud via LTE, using the...
Hi,
1) I want to collect sensor data using BLE like the following topology, the sensor devices are battery-powered, which sample in the NCS is suitable to modify?
2...
Hey guys, for testing purposes on nrf52833 and SDK 2.8.0 I want to use a simulation and stumbled upon bsim . I followed the instructions there and can build and run the hello...
I encounter this problem:
The radio_test application works correctly on the official nrf52840dk board, but cannot receive input commands on my custom product board.
However...
Hi,
I have been developing a PCB with an nRF9151 and a SKY65943-11 LNA among other ICs. I looked up the nRF9151 Development Kit (PCA10171) datasheet for some of the pinouts...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
we used SDK V2.6.2,
we used external flash for the OTA,
when we do the OTA after the NVS flash is erase so how we can solve this,
we used nvs_storage for this,
EMPTY_0...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
