Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hello. I am having problems when I connect one of my PCA10056 boards (nRF52840-DK) to my Windows machine and run nRF Connect v3.0, Bluetooth LE app v2.3.0. When I select the...
Dear Friend,
Using this tutorial I imported a Blank Blinky Kiel Project of SDK 12.30.
I am using a custom board with nrf51822, I imported the PCA100028 version.
...
Hi,
i am working on power management for nrf52832. i used icm20948 for gyro and accelerometer. my battery capacity is less. so when my mcu is going to sleep but gyro and...
Hi,
What is recommended to do for update SEGGER Embedded Studio for ARM 4.12 to newer version?
Is there any update tab from SEGGER or I need to download and install from...
Hi all! We have to work with PPK and nRF52 DK. For a measurement was used Power Profiler application from nRF Connect tool.
Is it possible to do the measurement in interactive...
The Interface MCU Firmware link provided on the nRF52840-DK page is the same as the firmware for the nRF52-DK. Unfortunately, these boards use different nRF MCUs. Loading...
I'm using Windows 10 latest updates installed.
I can successfully build v0.4.0 but none of the other releases of lte_ble_gateway
The common error is as below, any help...
Hello,
In our project there is a problem that we encountered is happening when the Nordic BLE mesh advertising and connectable advertising for GATT connections are enabled...
Dear Nordic.
I am manufacturing PCBA product using nRF52810-QCAA
My customer request to me about environment and Minerals report
I need three type of documents as...
Hi all,
I am trying to "add" the DFU bootloader to my application and I have some questions regarding it:
my thought are:
add to DFU bootloader example code, part...
Hi, After compiling the at_command example form the new release v1.0.0 and updating the nRF connect tool to version 3.0.0 I get the something that looks like bad baud rate...
I am using J-Link debugger.
I am programming nrf51822. On the Jlink commander my desktop sees my J-Link Lite CortexM device.
When I try the run an example on keil5 I got...
Hi All,
I used app_uart_fifo.c and it worked however RX is not good so I switched to LIBUARTE.
The RX part is good with LIBUARTE however when TX traffic is high nrf_libuarte_async_tx...
Hi,
I am using the nrf52832 dk
i am using the uart code from the sdk.
how do i clear the rx_buf and tx_buf (buffers) and set the pointers to the beginning of the buffers...
I have read through the USBD section in the nRF52820 datasheet and I think I cannot do what I need, but wanted to confirm I am not missing something.
I would like to make...
