Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
It looks like even with the latest SDK 1.6.0, the full modem firmware pre-validation is turned off.
It looks like this is a modem firmware feature, so it would seem that...
Hi All,
I am new in the Dev Zone and apologize in advance if the question was posted in the incorrect section.
I would like to run the Thingy91 as tracker hardware for...
Is there any API (software) available to evaluate DWM3000EVB module on nRF52 DK?
Can we use the API/software available for nRF52840-DK for nRF52-DK as well?
From where...
I am following https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.0/nrf/gs_installing.html for installing on Linux.
I have installed SES from 1.6.99 documentation...
I am trying to get use the Zephyr console sample for nrf52840dongle but when I have configured the following in my prj.conf file I get a link error.
When I reload the...
Dear friends,
From this case , we already know that the mesh stack will arrange a new block when the node is reset, so we will get a new sequence number. We will use the...
Hi, dear Nordic team. I would like to use buttonless OTA DFU for nRF52805.
Here is what I did:
Step 1) install all tools
Step 2) Build my ADC code, rename the output...
Hello
I'm going to use 'frequency hopping' to prevent frequency interference.
I don't know what frequency hopping is yet. May I have a good example and related documents...
Hi there
We managed to send/receive SMS on the nRF91Dk using the asset_tracker_v1 example, which contains the at_client.
However, with the asset_tracker_v2 we never...
Hi all,
Here's the context -
Hardware :
- nrf52840 DK
- sensor - LIS3DH connected via SPI
Software:
- SES
- nrfConnect
I need to send data being captured...
I've been trying to write a simple I2S loopback project for the nRF5340DK board using SES. Zephyr's documentation doesn't list I2S as a supported peripheral for this device...
I updated the firmware according to the video "https://www.youtube.com/watch?v=xQ7hDzRULJQ&t=314s&ab_channel=NordicSemiconductor"
File for "update modem" : mfw_nrf9160_1...
Good morning everyone,
I have questions regarding the initialization of UART communication between nRF52 and nRF91 on nRF91 DK.
Device HW/SW setup:
nRF52 DK: Bluetooth...
Hi!
We recently developed some firmware using S112 on a nRF52810 but realised that we needed data length extension, so changed to using S113.
Previously everything worked...
