I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Recently I have encountered a software hanging issue on one of our products. It was based on nRF52840, with FreeRTOS (Thread SDK v1.0). The issue was apparently related to...
My application needs to keep time and support local time as well. I have implemented a service that allows setting the epoch seconds as well as a local timezone string. With...
Hello, I have an issue with the init packet on SDK13.1. i used nrfutil to generate the .dat and .bin files that i read with Hex editor to transform then into byte arrays....
We've purchased the nRF6700 (nRFGO Starter Kit) and nRF24LE1-F16Q24-DK (Dev Kit) from Mouser Australia.
Both products arrived without Product Keys - so can't download any...
Hi all,
I am using the S332 softdevice for dual ANT/BLE stack in SDK v14.2 bundled with bootloader_secure_ble, which was apparently power optimized in SDK v15.0.0 (see my...
I have made a custom board based on the raytac NRF52840 module (MDBT50). When i load in the USBD CDC example (SDK version: 15.2), The device is not detected. There is no output...
Hi, I would like to build a mesh network with ANT so I tested the ANT scan and Forward example for nRF52832. And the current consumption is around 5mA, is this current normal...
As in the title, I installed 64bit nRFgostudio, however it crashes just after opening with the log below. It opens fine when I do not have my Thunderbolt 3 docking station...
Hi,
How can I send message from servers other than 0x105 and 0x106 to client?
I receive status message in client from servers 0x105 and 0x106.
I can send message to...
I'm trying to use the SDK 15.0 saadc example with a potentiometer on AIN0, and I'm getting weird values. Left pot pin connected to VDD, right pot pin to GND, center pin to...
Hi Nordic:
I want to add some rtt log in the bootloader code, so I make bootloader flash start at 0x77000, size is 0x7000, and my application's FLASH_PH_SIZE is 0x77000...
Hello, I read in the documentation how to create a model, in the client model, which defines a struct: simple_on_off_msg_set_t {uint8_t on_off, uint8_t tid}. I do not understand...
See: http://www.keil.com/forum/63929/
Everything here refers to J-Link, eg devzone.nordicsemi.com/.../a-working-demo-of-monitor-mode-debug-mmd-on-sdk-15-please
and Google...
Hello,
I am wondering that what exactly are the differences between libmbedcrypto.a and libmbedcrypto-software.a?
I read through the SDK documentation about the opethread...
In SDK 15.2 in ble_gap.h
#define BLE_GAP_SCAN_WINDOW_MAX 0xFFFF /**< Maximum Scan window in 625 us units, i.e. 40,959.375 s. */
#define BLE_GAP_SCAN_INTERVAL_MAX 0xFFFF...
