Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi there,
When using a PIN as RESET, what is the minimum activation time required to insure a reset?
I thought this should feature in Table 16.10.3 but I could not figure...
What is the logger message pool? There are two main definitions for it:
NRF_LOG_MSGPOOL_ELEMENT_COUNT
NRF_LOG_MSGPOOL_ELEMENT_SIZE
However it is not clear what it...
Hello ,
I want to use the NVIC to manage the interruption of the accelerometer and to run a specific program, are you ideas about the possibility of this?
Best Regard...
hi,
I am using nrf 52 DK and softdevice S132,PCA10040 board . I need to toggle a pin,set a pin,reset a pin .can anyone take this ticket to a sample code/ code snippet and...
Hi,
I have a project with 52810 which I use rc for LF clock source and I need use P00 and P01 as general GPIO, I have set both CLOCK_CONFIG_XTAL_FREQ and NRF_SDH_CLOCK_LF_SRC...
We are developing an nRF52832-based circuit with 1.8v power supply, which features BLE, NFC, SAADC, I2C & SPI.
According to datasheets, all 3rd party components are also...
Hi,
we plan to use the nRF52832 for a new project, I have two questions:
LE secure is supported, is this right ?
We want to pair up to 8 phones with our device....
Hi,
I am using SDK 14.2 with nrf52840 board. In my project I am using USB and BLE together. I have noticed that when I enable the LE Secure pairing and after that my USB...
Which nrfutil version should be used with Mesh SDK?
Getting started for Mesh has the link to nfrutil verison 0.3.0.0. In pc-nrfutil github repo the latest version is 3.5...
Hi!
I try to do simple led blink on nrf51822 and after build i got this:
Checking project status
Building ‘dongle’ from solution ‘dongle’ in configuration ‘Debug’
Compiling...
Hi,
I am using Segger IDE and now I wanna to use the temperature sensor presents in the PCA10040 board.
I tested the SDK example using the keil and works fine. When I...
I have your NRF52 DK and beacons.
I want to make the case so that my Nordic NRF52 DK will get data from Nordic beacons and forwarded that data on the UART port of PC....
Hi there,
I am developing a BLE dongle, and a BLE peripheral both based on NRF51822QFAC. The BLE dongle scans, connects, and disconnects the BLE peripheral by UART commands...
Hi
I get the following compiler (assembler) error in my project:
... Compiling file: hardfault_handler_gcc.c /tmp/ccstUNqW.s: Assembler messages: /tmp/ccstUNqW.s:46: Error...
Hey All,
I'm using the nrf_drv_uart UARTE driver (NRF52832) communicating with an external device. The UART init code is executed using a function (call all_main in this...
