Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
Hello everyone,
I'm programming nRF52833 for my own application. In my application, I have a button to turn on and turn off the supplier. There is only 1 button so that...
Hello,
I contact to you because a customer bought the bluetooth development tool part number NRF6939, and they asked the following below;
"
Can you specify whether there...
I have been testing a sample project that has compiled and worked fine for a week. But now it is giving build errors related to Zephry.
I think a broke a configuration,...
Dear Nordic FAE and fellow engineers,
I am using a custom board with nRF52832 WLCSP and I am trying to program it via SWD using NRF52DK PAC10040, and SES for programming...
I used armgcc and built out nrf52810_xxaa.hex (file size 60656) in
nRF5_SDK_17.0.0_9d13099/examples/ble_peripheral/ble_app_beacon/pca10040e/s112/armgcc/_build
I used...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
My I2C communication...
I desgined a PCB based on the nRF52840 module and led out the SWDIO and SWDCLK pins to Micro USB.
I used jlink v9 and connected three pins in SWD download mode. The SWDIO...
We have developed a custom board based on nrf52810 SoC (package : QFN32) , after following the guides on the forum we tried to run the example ble_app_uart(pa10040e) from...
Hello, I couldn't find any examples of SPI usage with nrf connect sdk, where can I find them?
At the beginning I want to do pretty simple thing - just send array of bytes...
Hi noridc,
I am using the sdk 15.03, s140 and the nrf52840.
I used as a reference the ble_app_interactive experimental example and the ble_central/ble_app_hrs_c. My...
Dear Community, good morning
I am working in a design that do not use USB port. If VBUS pin is left floating could it cause any issues to nRF52840.
Best regards,
Hello, guys!
I have some questions concerning GPS receiver inside nRF9160. You say in your documentation that GPS receiver supports L1 C/A reception - link .
There are...
What's the easiest way to view all logs and error messages using USB serial connection app like putty, on the nRF52840 dongle?
What drivers and functions do I need to enable...
