I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
Hi,
I am using the TWI scanner example from the sdk15. Board is NRF52840. I have a differential pressure sensor connected to the TWI input pins on the nordic board and am...
Hello!
Trying to capture and print the rssi values for all simultaneous connections from the multi_central example. I'm using an nrf52840 SoC that will be connected to four...
Hello, I am looking to use the thingy 52 as a remote sound recording device using BLE connection. I also have downloaded the source code for the thingy app and my question...
i want the ble_app_uart.c example to advertise also . so here i want to merge the ble_app_uart central +peripheral uart right ?
what are the changes i need to do
...
Hi Sir,
According to the datasheet of 52840 (v1.1), in the ref. schematic, the requirement of 32M is +/- 40 ppm.
In section 5.4.4.2, for the frequency tolerance requirement...
Hello,
Please comment on the expected difference in achievable range using 20 dBm vs. 23 dBm output power. Any details, assumptions, questions, etc. would be appreciated...
Hi, I'm looking for a more modern transceiver than nRF24L01 + and that works for the same. I am looking for a low or ultra low power transceiver that allows the implementation...
Hi, For my POC I use nrf9160 dk. Nrf52840 is used for scanning ble devices and nrf9160 dk is used for sending data to mqtt server (very similiar to one of the examples with...
Hello there!
We would like to use INT1 pin of ADX362 low power accelerometer on Thingy:91 board to interrupt nRF9160 (e.g. wake it up) when some motion is detected.
To...
Hello,
I am currently designing a new board using the nRF9160 chip and looking for an alternative component to use instead of the GPS RF Amplifier QM14501 and RF Switch...
I need to exchange data between nrf52840 and Linux PC. I see example project in nrf5SDK/examples/peripheral/usbd
Can anybody advise any example project for Linux C/C++ to...
Hi,
I'm working on nrf52840. As far as I understand, that device supports connection to peers with BLE 4.2 at least.
However, I'm able to connect via my phone, which...
Hi,
I have some questions regarding the state of the GPS functionality, and the future plans for nrf9160.
Will continuous GPS tracking while simultaneously using LTE...
Hi,
We are working with DK nrf 52840 and developing android app with nrf mesh library. is there a way to receive the feedbacks to the provisioners when any generic clients...
Hi ,
1-) Is there any dma half transfer interrupt ? if there is where it is in documents ? ( i check this link but i couldnt see anything about this https://infocenter.nordicsemi...
