Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
Hi,
I need to use
p_status->action == RELEASE_ACTION
to set the brightness level, but the p_status->action only gets updated after the loop finish so:
if (p_status...
Using the Border Router Quick Start Guide I've created the following setup.
2 Raspberry Pis, each with their own nRF5280-DK running RaspPi_OT_Border_Router_Demo_2.0.0...
Hello,
I am using nrf52840 with OpenThread stack. While I am using FDS to store application data, it seems the OpenThread dataset is written in the same area. Thus, the...
Hi to all. We develop new battery sensor based on nRF52832.
We already have an experience with Li SOCL batteries ER14505-VB 3.6V, and satisfied with it. Have in stock also...
I use sdk15.2. bootloader nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble_debug. Application nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_buttonless_dfu...
Hello, I'm currently attempting to display a screen during an OTA-DFU process. First and foremost, through BLE, a BLE Central will command my BLE Peripheral to commence DFU...
I am working with NRF52832 master with TWI slave device, however , since our board already has external pull-up resistors (10K) , how do I disable TWI internal pull up resistors...
Hi nordic
I am using SDK 14.2.0 Softdevice s332 5.0 Board nrf52840.
I am doing test about DFU example and I am writing in flash about test image.
It is possible. I made...
Hello.
We have a working DFU system using Nordic's Secure Buttonless DFU bootloader. The bootloader correctly checks if the incoming DFU package has the correct 'init packet...
Hi all,
I am curious about the storage capabilities of the Nordic Thingy. I would like to store information about the received messages like a timestamp. How much data can...
