Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello, I'm programing my project while using the nrf52840 chip. I'm using segger embedded studio for the programming part because with the nrfconnect I have error code 9 ...
Hi I wish to integrate Matter over thread in unicast audio server . My objective is to use matter to control the volume and play/mute states. I would like to know whether...
Hello, checking if it's at all possible to have uart working on the nrf52832-dk using pins 18 and 21. I can get rx/tx working with an ftdi using pin 12 & 13, but not 18 &...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...
Hi,
I have thingy:53 and I have damage to the sw2 pin and I am unable to enter the DFU. I lost two tiny pieces that go just above the one in the photo and not even...
Can some one describe how this is supposed to work:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/mpsl/timeslot/README.html
I would have expected to see...
Hi,
I wonder if anybody could help me? What is the best way to close down the nrf9161 so that it reconnects quickly after powering back up again?
I'm running Zephyr 2...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
