Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello.
1. For nRF5340 DK, in normal voltage mode, I use putty(windows) and minicom(Ubuntu) to view the printk logs, it works fine.
In high voltage mode, which software...
I am currently trying to test the writable ndef message example on my nrf52 development board. I have gotten it to work so many times in the past weeks but now it seems when...
It seems like there is a problem with nRF Connect 3.7.0 with Toolchain Manager 0.9.3
When I try to open I get the following error.
I have tried restarting and reinstalling...
I'm having trouble connecting the Thingy:91 to LTE network.
I'm using the thingy91_fw_2021-06-28_7a076c22 example.
I flashed correctly the thingy91_asset_tracker_v2_nbiot_2021...
Dear Nordic team,
We are deveopping BLE & ANT enabled display. Because it is a mass production product we need to do an automation for asigning devices destinguesed ID....
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
Hello,
Out application is using the time slot api to generate ~29ms (35Hz) burst of pulses.
Occasionally, the interval between two adjacent pulses extends to ~35ms ...
Dear Nordic support,
I need to clarify a few points using SAADC for battery measurement - running the ble_app_proximity application without modification. I measured the...
hello, i hanve a problem when i use usb transfer data to pc with ep1, sdk 17.0,nrf52840dongle
I have many data(more than 100KB) transfer to pc,when I send the data for once...
Hello,
I am using the nrf52840 for the application, basically i want to use the timer driver in my code.
so basically if i have 5 timers of nrf52840 and i am using one...
I am using a nRF52840 Development Kit to flash a custom board with a nRF52840. When I use the nrfjprog -p (or --pinreset) option to reset the CPU, it will consume over 1mA...
I am using nRF52833 on ncs to turn on the extended broadcast. After referring to the corresponding settings, I found that the transmit power setting does not take effect....
In standard sdk 17.0.2 is it possible to know which devices did i accidently disconnect?(Interactive command s140)
for example
my central is the interactive command...
