i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
We have encountered a problem in using iic to communicate that the delay cannot be removed.
We are using the sample in NCS,
the address of the sample is C:\ncs\v2.6.1...
Hi Nordic,
We are develop a multiple switch button device based on nRF54L15. We've two issues now while developing.
1. Matter Network Commissioning Issue with nRF54L15...
NCS 2.9.1 - NRF5340DK
I am trying to use multiple compare channels on Timer1 such that an interrupt handler fires for both compare values, the second of which is enabled...
Hi everyone,
I am currently studing to flash the MDBT50Q-DB-40 demo board from RAYTAC. I used the following site as reference. https://docs.nordicsemi.com/bundle/ncs-latest...
Hey guys,
I'm working with the Laird DVK-BL652 and the Nordic SDK v.14.2.0 with Eclipse (Kepler) and try the example "SPI Master". I didn't modify this example but after...
Test Setup:
SD 6.1.0
SDK 15.2.0
Peripheral: nRF52840
Central: iOS 13.1
Central is connected to two peripherals, each peripheral is sending 50 pkt/s, each packet...
Hi,
We have a nrf51822 based custom board with no button, we use accelerometer tap detection to wake up the system. Currently there is no software protection for the battery...
After getting my nRF9160DK activated and showing up in the NRFCloud it would just sit there blinking led3.
I deleted the device from the cloud and tried to update modem...
i create device information service BLE_UUID_DEVICE_INFORMATION_SERVICE,and Bonding on the phone.
i want to update the PNP_ID_VENDOR_ID and PNP_ID_PRODUCT_ID，
method 1...
Hi,
I'm using NRF52832 DK to integrate the LittlevGL graphic drivers . I'm facing some problem while integrating the sdk's.
I'm getting the errors:
.\_build\nrf52832_xxaa...
I have found what I believe to be a bug with the nrfx_qspi driver on NRF52840. After using the QPSI peripheral, I have found that in some cases the NVIC's IRQ#41 (QSPI Interrupt...
Hi,
I am using nRF52840-DK with Segger Embedded Studio . In this dev kit the Atmel chip ATSAM3U2CA-AU provides the programming/debugging interface. In order to save BOM...
Hi,
I'm using commands below to send SMS message in my application. SMS sending is working fine, but some reason during the AT+CMGS command program execution
Is blocked...
I understand that I have to get approvals for my product, but can the nRD9160 operate globally?
Has this sip already been approved (on other pcb's) for use on Verizon, AT&T...
Hello
I'm testing a DFU right now
By the way, the icons coming out when advertising in the APP today changed to the Christmas version, it seems a little weird.
Originally...
I am trying to implement PA + LNA to nrf_esb.c, if I set in PA constantly ON, receiver gets good signal but sender cannot get ACK, if I set LNA constantly ON, receiver signal...
On the Mac machine, I open the Bluetooth Low Energy app of the nRF Connect for Desktop, connect to the nRF52 DK, and try to find the button to perform bonding, as the SDK...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) Initially I loaded Secure serial bootloader...
Hi there,
I'm developing an application that needs to store data points when internet connectivity isn't available. Is it possible to write small packets of data (lat/long...
