Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
Hi,
I am using nrf52840 to develop a product. I use NCS sdk v2.5.0.
I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
Trying to get this working
err_code = nrf_ble_scan_filter_set(&m_scan, SCAN_ADDR_FILTER, AddressTable[Index].peer_addr.addr);
The error code returned is 7. Not sure what...
Hi,
1. Is there an example to show how to send a door lock cluster events command?
2. How to check door lock cluster events by CLI(@coordinator)?
Best Regards
S...
What I did was creating a timer and reading the temperature/humidity data from a DHT22 sensor in the timeout handler for every 2 seconds. Everything is fine with the data...
I have successfully created the model and i have added the model using access model add function
now i have an error in check_tx_params. I tried to use
dsm_address_publish_add...
Our BLE app (based on ble_app_uart, example) on NRF52832 normally enters sleep by sd_power_system_off(). So this works as expected.
However, if we load the app by secure_bootloader_ble_s132_pca10040...
Hi,
We are using NRF 15.03 SDK and used NUS application for the project. We need to store some data into flash and we are using FDS example based code to do the same.
...
Background
I am attempting to build a system in which a Nordic NRF52840 SoC, is connected to a mobile app (iOS / Android) via BLE and both devices play back audio-visual...
Hi all!
Resoldering usual QFN packages with pins along the edges is not such a big problem... but how is this usually done with devices they have pins underneath the package...
Configuration: 52840 / S140 / V610, SDK 15.2
As approaching production, I am continuously testing S140 on various environments.
I noticed during testing that there are...
I got Thingy:91 and want to install at_client to it, but it doesn't work well.
What I did is
1. Check out a pull request and update firmware referring to this link ...
Hi everybody,
I work on custom board with the SDK 15.2.0 and the SoftDevice S140.
I work on the ble_sdk_app_template example. I tested it on the nrf52840 DK and it work...
Hi,
I am a beginner in nrf52840 DK. I am trying to run TCP example. I have flashed client example in the DK and able to connect to the laptop(LED_2 ON). When I press BUTTON_1...
Hi There,
This is Particle's Sr. Hardware Engineer, Ping. We are working on a SoM (System-on-a-module) called EG91-SoM that with a nRF52840 (Thread) + EG91 module for acting...
Hello,
Hardware: NRF52840, Development Software: any
I am hoping to generate 3, or ideally 4 separate (independent duty cycles) PWM signals at a frequency of at least...
