I upgraded the SDK to 3.0.0. and now I have an issue:
"Actions/Flash" command fails with "Timed out waiting for RRAMC.READY.". "Actions/Erase and Flash" works.
I am on...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi,
i have developed a Windows based App in Qt that using BLE.
My problem is upgrading a remote device Firmware using BLE.
Did exists any type of C++ class automator...
Hi Nordic!
I faced a problem when I want wake the MCU up from SystemOFF.
When my nRF51822 is in SystemOFF mode, a watchdog chip wakes up the MCU. After sending the...
Hi.
I think i just fried my NRF52840 dongle. VDD out is only about 0.5V :| I'm currently powering it from the usb port (VBUS is correctly +5v). Could it be that Ii only...
Hi,
I"ve designed a custom board with the MDBT50Q module (part of the schematic below). When writing my program to Flash 0 and Ram Memory 2000 0000, the program won't load...
I have been experimenting with the example of the MQTT Client Subscriber/Publisher from de nRF SDK. I use:
SDK v15.3.0 (also nRF5 SDK v15.2.0).
Raspberry Pi 3 (as a...
Are there any working projects that integrate TWI and MPU6050 sensor. That are edited by KIELu5 and follow the SDK 15.3v ? I tried modifying the 'twi_sensor' project but I...
Good day
Im trying to switch off an LED when my relay/hopper is not advertising. I switch the LED on successfully when transmission starts but I'm struggling to do the sd_ble_gap_adv_stop...
Hi, everyone,
now I'm test " \ncs\nrf\samples\nrf9160\gps\build_nrf9160_pca10090 ",
it's error about" nrf_socket.h: No such file or directory"
I'm find the file at ...
So this is a small continuation of this ticket https://devzone.nordicsemi.com/f/nordic-q-a/50656/using-pdm-mic-on-nrf9160dk .
The problem I'm having now is that when I run...
I wrote UART echo sample based on ble_app_uart_c for S140/ nRF52840-DK.
When nRF52 receive one line on USB/UART, it send same line to USB/UART.
I also write Linux socket...
I am following this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentId=43347679-22d9...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
Hello, Currently, we trying to use PPI with the SPI module (we use the SDK 15.3.0) We expected that the SPI makes one read transaction every 5 us ; to do this, we use 2 PPI...
