Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
Hello Nordic Team,
I am requesting clarification on the capabilities of my nRF9151DK to be used as a debug and flash probe (via the 'debug out' P20 headers), and compare...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
hi,
i want to use mesh network in my project.our requirement is multiple nodes will be sending data to one master node.is there any example code.
Regards,
jagadee...
Hi,
We have a gateway device that contains the nRF51822 MDBT40 Raytac module.
We are designing a new nRF52832 based sensor and we want to connect 20 of them to the Gateway...
I use nrf_drv_saadc_init(NULL, NULL) to sample AD per second(Blocking type).
But every time the firmware runs, the ADC value always takes several times to stabilize.
...
when trying to initialize the nrf52...little bit confused how to specifically address a pin for i2c....can anyone help me with a piece of code.
Thank you in advance.
Hi. i'm using IAR and St-link to program the nRF52832, and run this tutorial on my custom board, but the Bluetooth has not been set up by the method that you proposed. and...
Hi guys, I have a question about ble_app_uart_c example in SDK. (I'm using the latest SDK, 15.3)
And my board is nRF52 DK, which is PCA10040.
While I'm testing ble_app_uart_c...
Hey everyone,
i would like to use the NRF52811 with the new Softdevice S140 V 7.0. Therfore i took the ble_app_blinky (pca10056) example and changed some preprocessor...
I am using parts of the ANCS example code within a product near pre-production. I am able to reproduce the problem in the ANCS example without modification. Here are the specifics...
Hi,
we are using nRF52832 for beacon application. we want to find the low battery condition.
Does nRF52832 have option to read the voltage level? if so please share api...
Hello,
I have created a custom board that uses a NRF52840.
From my understanding, i'm need only VDD,GND,SWDIO and SWCLK connected to the SOC to flash them by using an...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi,
We have been using nRF52840 in QFN package in a BLE application. Due to size considerations, we want to upgrade to the WLCSP. I saw that the tuning network is different...
Hi,
We are using nRF52840 DK with 15.3 SDK (latest).
Registered at thisant and got the s340 softdevice for nRF52840 DK.
Please answer are my questions
Where...
