Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
Hello,
I'm trying to use the mesh DFU on 2 nRF52840 DK by following the quick start guide and it didn't work.
Using the mesh sdk 2.0.1 I made the below batch file as described...
Hi,
We need a BLE chip which can be used as a radio which supports BLE SIG mesh and work on standard HCI commands.
Kindly suggest the right device.
Thanks & Regards...
I am using a Mac with SES installed. I created a DFU example and downloaded it to the Thingy 52 to see how it works. That all went fine. Unfortunately, it has disabled the...
Hi all, I'm trying to evaluate nRF Connect SDK, starting with guide in nRF Getting Started Assistant app. So far I've executed every step, but when I try to open the project...
We are using nRF52810 and SDK 15. We have to save up to 50 bonding information.nRF52180 is knowing to save up to 4 bonding information. Can you save up to 50 bonding information...
Hi,
we are trying to use FAT file in nRF9160. Referring the test case in "ncs\zephyr\tests\subsys\fs\multi-fs\src" to mount the FAT file.
But getting an error like "ff...
Hi I am migrating my application from SDK - 12.3 to SDK 15.3 version.
My application also uses FreeRTOS so I am referring to the ble_app_hrs_freertos example code.
I have...
Dear,
I am trying to test BLE on the nRF91 DK, I found an example: \nrf\samples\nrf9160\lte_ble_gateway
I tried with the master branch , but I got the error:
Then...
Hi,
I received my nRF9160 development board a week ago and tried to program it using the following guide:
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts...
Hello Everyone,
I'm currently developing a SoC and I would like to achieve a correct interaction between the SoC and the Nordic Nrf52832.
The output of the SoC is...
After a DFU, when the new firmware is booted a service changed indication is not being sent so iOS only sees the DFU service. Should the softdevice be sending the service...
Hi
We can't connect jlink to nRF52840,then we check the voltage of DEC pins, Is this correct?
And what's the function of DEC pins(DEC1\DEC2\DEC5)? The datasheet description...
Hi all
I have an identical problem to this: https://devzone.nordicsemi.com/f/nordic-q-a/51567/can-t-build-nrf-connect-project
All my setup is the same, and the problem...
