Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello Nordic, I'm reading: creating new modes in sdk documentation. In the simple_on_off client model, I do not understand the place I underlined in the picture. When is the...
Hi,
I'm looking at prototyping something for very small volume and looking to go the 3rd party module route ( www.nordicsemi.com/.../3rd-Party-Bluetooth-Smart-Modules)...
Hi,
I'm trying to capture Mesh packets using nRF Sniffer 2.0.0 and nRF52 DK while running the Light switch demo, but so far I haven't been able to capture any packet that...
Hi,
I'm having an issue when responding to rw_auth requests on the nrf52840 w/ sdk 15.0. When I'm attempting to update the table, If I make the length too large then it...
Good afternoon,
We just migrated our peripheral application, working perfectly on the nRF52840 DK, with SDK15.0.0 and SoftDevice6.0.0, and it is now crashing with SDK15...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
Hi,
I have tried the following example: infocenter.nordicsemi.com/index.jsp
Everything works fine (I can generate a notification via a calendar event and see it via the...
I get NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add(); If I comment custom service initialization where is this function I get the same error NRF_ERROR_INVALID_PARAM...
Hi, For a new project we need a smaller devices compared to to the nRF52832 dev board but still want to stay with the nRF52832 chip without making our own PCB. As an alternative...
We have a large number of units in the field running on SDK 13.0.0/S132 SD 4.0.3 and in order to add new functionality we need to migrate to SDK 14.2.0/S132 SD 5.0.0 via DFU...
Hi,
This is a follow up of issue: https://devzone.nordicsemi.com/f/nordic-q-a/28211/thread-dfu-upgrade-problems/111436
We're trying to perform DFU by following "Thread...
nRF52810 only supports S112 so the max throughtput anyone can achieve is 330 kbps .. please provide proof.. test data. Only nordic employee please answer this or someone who...
