Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
I have nRF52832 as my development kit. Currently I am testing various ble peripherals i.e Blinky , beacon etc. Now I have to test IR sensor with the Development kit .I aim...
Hello,
I used a the ble_app_template example to set up advertisements on the PCA10040 board and on our custom board. Both boards function and have good signal strength....
I build ADC example from SDK12.3.0 for nRF51822 QFAA chip from source. I used custom board and changed the pin configuration for UART logging in sdk_config.h file.
But unfortunately...
Hi All,
I am performing OTA-DFU - Generating our own packages on my nRF52DK. but when i am trying to generate zip but i am getting some error , below is the screenshot for...
The aQFN app note suggests a fully open paste stencil (opening size = pad size) for the center pad of the aQFN.
Our assembly house is suggesting a windowed paste stencil...
Hi,
I have a question about the time period being used as waiting time before sending a reliable message is retried, this until an ACK is received or the timeout is reached...
I have a Central + Peripheral running on the nRF52840 (SDK 14.2.0). I have it configured to automatically connect to 3 Peripheral connections and allow 1 Central connection...
APP_TIMER_KEEPS_RTC_ACTIVE SDK15.0 rtc does not start unless at least 1(one) timer is active
I have set APP_TIMER_KEEPS_RTC_ACTIVE=1
And I want to use the app_timer module...
In all instances where the internal function `hash_algorithm_get()` is used in `cc310_lib_hash.c`, the output is inverted, making would should be a successful return code...
I have designed my customized board according to the nordic's indications, adding the components for the LDO and DCDC recommended. Now I am selecting the battery that I will...
Hello,
We are developing a system in which a device controls a host and the device should receive status information about the host. In some use cases multiple hosts are...
Hello everybody !
I am looking to connect 2 cards nRF52 DK (52832) with another card nRF52 DK (52832), a little like the fact my smartphone with these 2 development cards...
Hi, all.
I'm making a mqtt client with nRF52832.
All examples of SDK 14.2 were using PSK secure.
But I want more secured connection as like MBEDTLS_TLS_RSA_WITH_AES_256_CBC_SHA...
Hi,
After sd_ble_gatts_hvx() call, is it possible to change or delete value in softdevice buffer before a connection event ?
Thanks by advance for your help
Best regards...
