We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I am just wondering if it is possible to use the 52840's USB interface to create an R/NDIS type interface . The intention is to maybe create a WIFI/Cellular based Network...
Hi,
I am testing ble_app_att_mtu_throughput in SDK 14.2.0 between two nrf52832 DK board. One is act as a central and other one peripheral. I am placing these two boards...
Not a question, just to tell you that in ble_gatts_attr_t Struct Reference, documentation of « uint8_t* ble_gatts_attr_t::p_value », a « @ref » Doxygen markup has been produced
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
Hello,
I've got the light_switch example running. I would like to extend this example with the possibility to send a broadcast messages from every node, the light client...
Hi, We are facing issue with updating firmware using NordicSemiconductor/IOS-Pods-DFU-Library. we are unable to upload new firmware and getting failed operation at the time...
Hi,
although the NRF52840 has a nominal receiver sensitivity of -103 dbm I am only able to get a sensitivity of around -97 dbm. I know there was a bug in older soft device...
Hi all,
im using keil5 for this .i getting problem or may be confusion while selecting the packages .also could i use the softdevice for this .Also wanted to know the uart...
I want use two 52DK for BLE transfer demo, one 52DK download nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart",
other 52DK download "nRF5_SDK_15.0.0_a53641a...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device. Schematics are shown below
here BATTERY is connected...
The nordic thingy won't program anymore every time I try to program it gives an unknown error.
Does this mean that it is bricked and i need to change the chip or is there...
