Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
Hi,
I have a project with 52810, I met below build error when compiling dfu project:
.\_build\nrf52832_xxaa_s132.axf: Error: L6366E: uECC.c.o attributes are not compatible...
Hi
Now I'm using nRF52810 base on SDK v14.1 and I want to do the OTA for it. When I combile the bootloader project, I get so many error "No space in execution regions....
I just want to change the Advertising interval min and max values in ble_gap.h file in meta wear RG
so do I have to change firmware code or is there any other way to deal...
In the eclipse setup here
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development-with-gcc-and-eclipse
It give two links to example eclipse projects...
I can see that we can use APPROTECT to disable reading of the flash.
This seems to be reversible using: nrfjprog -f NRF52 --recover, which will erase the flash and allow...
I used SDK nRF5_SDK_14.1.0_1dda907.
I added cycling speed and cadence service of BLE and bicycle speed and cadence of ANT+ in ble_ant_app_hrm example of multiprotocol. ...
First - thanks to those who answered my question about the Segger Embedded Studio code size limit. It appears to have be fixed when I switch the build configuration from ...
I would like to use a Bluetooth protocol analyzer for sniffing traffic in my Mesh network. I need to input the devkey(s), netkey, and appkey to the protocol analyzer software...
