Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi I am using Jlink board(v9.3), when connected to my pc (window 7), I can't select nRF5x programming.
nRFgo studio version I am using is 1.20.0.2. I tried uninstalling and...
I am using the following code during stack initialization:
// Register with the SoftDevice handler module for BLE events.
err_code = softdevice_ble_evt_handler_set(ble_evt_dispatch...
Hi,
I migrate my code to FreeRTOS environment.
I use SDK12.2.0 ble_hrs_freertos code example as a startup project.
My question is how i need to init gpite?I receive...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
I have been able to get all the MPU based projects to work from this Github site (which has been very helpful!) with the exception of this one.
The accelerometer values...
For a device that has APPROTECT enabled, it is required to use nrfjprog --recover to re-enable access.
What is the mechanism that nrfjprog uses to perform the --recover...
With the nRF52, is the RTT functional when APPROTECT is enabled?
I would expect not since the RTT relies on memory accesses which should be disabled with APPROTECT
Hi,
In SDK11, it was possible to call app_sched_execute() from a function that was itself called from the scheduler:
void app_sched_execute(void)
{
void * p_event_data;...
If you dont have an external 32Khz crystal for the nRF52832, besides the higher power consumption, are there any other issues ? e.g. CPU starvation affecting my app during...
Hi all,
I work with a nrf52, my project send and receive Beacon data.
when i work only with 2 card all works fine but when there are several transmitter and 1 receiver...
I've got an nRF52 application which is based on the nRF OpenMesh github.com/.../ but has been vastly customised. The application either acts as a mesh device and allows a...
As the title，I recently want to use nRF51822 to communicate with SmartCard in ISO7816 interface. but I don't know how to do this.Can anyone share the example code online ...
Hello,
I am using the nrf sniffer from adafruit to pick up ble packets from my NRF52. Everything has been working fine for the past 3-4 months. Yesterday I wanted to test...
I'm trying to create a HID over GATT device that is not a keyboard, nor a mouse. About a week ago, I came close by being able to read some data in an OSX app from the device...
