Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi Engineers!
have a question about V/T/QFN package version instead of AQFN.
We prepare our PCB (China) for mass production so, need to understand possible packages...
I am following the example at infocenter.nordicsemi.com/index.jsp
The following line is giving me the error "Error[Pe065]: expected a ";":
NRF_QUEUE_INTERFACE_DEF(uint8_t...
Hi all
I'm working on a custom board using gcc and eclipse.
My primary problem is I'm fighting with the ld settings for the secure bootloader.
I activated the RTT which...
Hi,
I want to write calibration and configuration datas in to flash and read it back. By using sd_ble _flash_write API function , I can write up to 520 words(520* 4 bytes...
Hi, all!
nRF51822 had been used in my project, because of dual bank bootloader and softdevice, the
internal flash memory was not enough for the application. I want to...
Hi there,
I need to add more the function based on Bluetooth, and I need the better security of the function. However, I do not want others read flash data freely and I hope...
Hi
I'm preparing for some tests and I'm wondering where I can find information about what the expected percentage error rate should be?
Right now with 2 nrf boards connected...
Hello to all nordic jedi masters!
I have made an observation, on which I would like your confirmation.
My combo is: nrf52832 + SDK 11 + SD132.
Will my application ...
I'm currently writing my thesis, and my goal is to establish a network protocol like IP. We need to transmit about 200kB of data between 2 or more nodes once every 10-30 minutes...
I am programming a device with a NF52 that uses a hall effect switch o enter/exit sleep mode when BLE is in advertising mode. When connected, It will generate a separate BLE...
Hello,
i have a strange behaviour on a board with nRF52. The board is flashed with SD 4.0.2 and bootloader.
On Keil If i load the bootloader with JLink, it runs and...
I'm using nrfutil version 2.0.0 and have noticed a strange bug today when generating a new signed application image for bootloading.
If I have a version number of 0207...