Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi
I am using app_button library to sense button detect, it work fine.
static void button_init(void)
{
uint32_t err_code;
//The array must be static because a...
First of all I appreciate your help.I am using mesh example in https://github.com/NordicSemiconductor/nRF51-ble-bcast-mesh link .I can send data by providing connection with...
Hi Nordic team,
This problem bothers me for a very long time. I cannot find the root cause. I used nRF51822 IC. It uses SDK11 with softdevice S130 and bootloader (but I...
Using nRF52 with SD 132 3.0.0.
Peer manager uses fstorage to store information.
I need to be able to specify the address range which fstorage can use.
Is there a configurable...
Hi,
I have problem with both functions sd_ble_gatts_value on central device.
It works on peripheral, because there is my characteristics definition.
Now I have to read...
Hello,
I'm developing a BLE Application where I use the peer manager. My Goal is to use direct advertising after disconnection if a device already has bonded. But every...
I am using the SAADC on the nRF52832, SDK12.2.0, with it set to 12 bits and low power mode. I have enabled five channels which I run blocking nrf_drv_saadc_sample_convert...
Dose this capture from the Nordic Specification means that to read bytes from SPI i need to send before. Each byte i send i get a byte!!!
MLy case i have read only sensor...
I am using the nrf52832 with the s132 for a project in which I have a frame with 24 bytes that need to be transmitted through BLE.
I have followed the tutorials and I have...
Hi,
First I'd like to salute the great work done by you Nordic people for those open source and hardware.
I just installed the SDK 10.0.0, S120, gcc-arm toolchain, configure...
Hello, I'm a beginner with the BLE technology and nRF52 is a good tool to start with it.
Currently, I have a setup that allows a Raspberry Pi and an nRF52 to communicate...
Hi. I have a problem with programming brand new chips nRF51422.
I have connected: Vcc (1, 12, 35, 36), Gnd (33,34,13), Swdio (23) Swdclk (24).
christal on the board:
...
I had downloading many versions SDK,from 10.0.0 to 12.2.0.But when I Program SoftDevice then download the examples,such as the path:
nRF5_SDK_12.0.0_12f24da\examples\ble_central_and_peripheral...
hi,all.
when i first time connect nRF52840PDK to PC, and open nRFgo Studio, but encounter this problem:
no device detected.
screenshot:
I click recover button many...
I want to send several packages in one interval from my iphone to 51822(s130).But the demo ble_app_uart can only receive 1 package per interval（ipone6，lightbule，writewithoutreponse...
