Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
What should the connection or other settings be to have a peripheral always connected? It is a bit contradictory for low energy device, however for a lost&found (link-loss...
Hi,
I just started on developing on the nrf51-DK. I started with blue_app_proximity, and I am trying to hack the immediate alert to do a toggle a led. I initialize the...
Hi,
I am trying to save/restore some configuration variables to/from the flash storage. If I do it using S110, it works perfectly fine and I can both store and read values...
Hi,
I have the same problems as described in devzone.nordicsemi.com/.../
I'll post details here as requested. I do the following:
-Connect P0.30 to ground (see photo...
We are working on a BLE home automation application. It is likely that some homes could have 10 or more of our devices. We also need to allow the homeowner control of which...
Hi Team,
I am trying to implement Blugiga's cable replacement service in Nordic chip.
I have successfully changed required UUIDs for services and characteristics please...
Hi all,
Can I update the value passed to the sd_ble_gap_adv_data_set() to do a scan response at any time?
For example when I get an interrupt from a button, can I update...
Hello,
according to the BLE 4.1 spec, a device can be able to be slave in multiple piconets at the same time. Will this ever work with the S130?
I do not know how the...
Hi, Nordic Enginner:
Now i want to use a external mcu to programe the nrf51822 by signal bank hci dfu mode(BLE DFU,we do not need! ). Also we have a pc softawre for control...
Hi everyone :
I have some questions about nrf51822 ble S110 ,I have two ble device ,both device used S110,is it possible use the first device to scan the second device to...
Hi,
I used the pstorage example mentioned here and got it to work to an extent.
A snippet of my code is :
retval = pstorage_init();
if(retval != NRF_SUCCESS)
{
...
Hi,
I created an Android project that scans nordic beacons and parses the data in it (such as the tx level, major. minor, UUID etc). I'm doing some low level parsing to...
