Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi all,
I need to be able to reprogram an nRF52832 on a daughterboard from a mainboard with a Cortex M7. I have been able to eraseall and reprogram the nRF52, but it seems...
I have searched this site and not found an answer, although this seems to be a similar question: https://devzone.nordicsemi.com/f/nordic-q-a/41853/usb-driver-install-fail...
Hi,
I am stuck in sending and receiving serial data over Rx and Tx in nrf51 DK. I used arduino to prototype a fingerprint access control system. Now I am shifting to nrf51...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
Dear all.
I know the nRF52840 has 2 uart module.
I've been used only 1 uart setting like below pin connecting in 52840 DK reference doc.
But now i have to use 2...
*** Disclaimer *** I am a total rookie on this technology *** Disclaimer***
I'm working on a small BLE proof of concept and I have an nRF52840DK board. I've got Wireshark...
Hi, guys! I'm using the nRF52 SDK 15.3 BLE_APP_UART peripheral example.
I wish to add 3 ADC channels (12-bit) to read 3 potentiometers at a sampling frequency of 6kHz. ...
Hi,
I've BLE custom data sent to nrfcloud and looking for ways to plot data. I've used "add custom card" from configuration to extract data but was not able to plot/view...
hi, I am working on nrf52832 platform and tested some Bluetooth examples of SDK_15.3.0, I want to test some Bluetooth examples like audio, media and etc, is there any project...
Hi,
I am using a BLE master to bond with nRF52832. SDK is 15.3.0. Both side support secure connection.
I have tried to set the address type of master to public or random...
Hi, I'm starting to use the nRF52840 DK, I have downloaded the segger embedded studio but I don't have idea how to start, I need a sample example to use the pins to control...
I am new to Nordic products. I have a custom nRF51822 board and I want to flash it with Keil uVision and ST-Link V/2.
As I understood, I have to program the SoftDevice firmware...
